How Can Auto Mechanics Protect Their Hearing in a Loud Shop?
Impact guns, grinders and air ratchets often top 85 dBA. What shop noise studies found, and hearing protection that suits greasy, on-and-off work.
If you work in a repair shop, a collision shop or a tire bay, your day is a string of short, sharp bursts: the impact gun, the air ratchet, the cutoff wheel, the hammer on a panel. Foam plugs are a pain with greasy fingers, they work loose when you’re on your back under a car, and you still need to hear the customer, the service writer and that odd noise in the engine. So it’s tempting to skip them. Studies of real shops show the tools are loud enough that skipping them adds up, and the most useful protection is the kind that’s quick to put in, stays put and lets you hear the work.
Quick answer
- How loud are shop tools? In Minnesota collision shops, most tools measured above 85 dBA, and hammers, grinders and ratchets averaged above 95 dBA.
- Does a whole day add up? In Colorado tire shops, 60% of full-shift samples went over an 85 dBA guideline, with an average of 18 tire changes a shift.
- The surprise: some shop solvents can harm hearing too, and noise plus those chemicals can do more damage than either alone.
- What helps most: protection that goes in clean and fast, doesn’t block so much that you pull it out to talk, and is worn every time the air tools run.
How loud are impact guns, grinders and air ratchets?
Loud enough that you’d have to raise your voice to talk over most of them. In a NIOSH-funded study published in the Journal of Occupational and Environmental Hygiene in 2011, researchers spent three days in each of four small collision repair shops in Minnesota, measuring full-shift exposure and the noise from individual tools.
What they found:
- The majority of tools generated noise above 85 dBA.
- For air guns, wrenches, cutoff wheels and air drills, even the quieter end of the readings (the 5th percentile) was above 90 dBA.
- Hammers, grinders and ratchets averaged above 95 dBA.
- Full-shift doses stayed below the OSHA legal limit, but 4 of 18 shift measurements went over the 85 dBA guideline from the American Conference of Governmental Industrial Hygienists (ACGIH).
There’s a catch the authors point out: all the shops were having a slow period at the time. They concluded that during busier stretches, technicians’ 8-hour averages are likely to go above 85 dBA.
For context, NIOSH says that at around 85 dBA you usually have to raise your voice to be heard by someone 3 feet away, and at 95 dBA or more you likely have to shout.
How many tire changes before the noise adds up?
A tire bay is a good example of short noises stacking into a long day. In a 2021 study in the Annals of Work Exposures and Health, Colorado researchers took 30 full-shift noise samples on 20 technicians at three tire-changing shops.
- Shifts averaged 6 hours 42 minutes and 18 tire changes.
- None of the samples went over the OSHA legal limit, but 18 of 30 (60%) went over the ACGIH guideline of 85 dBA.
- Working from the upper end of their estimates, the researchers figured that fewer than 20 tire changes could be enough to pass that 85 dBA guideline.
- The air ratchet, the tire-changing machine and the bead seater all measured above 85 dBA.
The authors said the results pointed to the need for a hearing loss prevention program. In plain terms: an ordinary day of tire changes was enough to push most of these technicians past that guideline.
How much louder is too loud, and how fast does it add up?
NIOSH recommends keeping noise exposure under 85 dBA averaged over an 8-hour day. For every 3 dBA louder, NIOSH recommends cutting the time in half. Worked out from that 3 dB rule:
| Average level | Time to reach the NIOSH daily limit |
|---|---|
| 85 dBA | 8 hours |
| 88 dBA | 4 hours |
| 91 dBA | 2 hours |
| 94 dBA | 1 hour |
| 97 dBA | 30 minutes |
Tools aren’t running all day, which is why shift averages come out lower than tool readings. But every burst counts toward the total. NIOSH also lists signs that a day was too loud: your ears ring, sounds seem dull or flat when you leave, or you turn up the car radio on the drive home compared to the drive in, then find it too loud the next morning.
Can shop chemicals affect your hearing too?
Here’s a less familiar part of the picture. NIOSH explains that some chemicals can damage the ear, including solvents such as toluene, xylene and ethylbenzene, and carbon monoxide. They can be breathed in or absorbed through the skin. NIOSH also says that being exposed to loud noise and these chemicals together can cause more hearing damage than either one alone, and it lists painting and fueling vehicles among the jobs that can involve both.
Earplugs don’t help with chemicals. NIOSH’s advice there is better ventilation, safer substitutes where possible, chemical-resistant gloves and a properly selected respirator. If you paint, prep or work around solvents, it’s one more reason to take the noise side seriously.
Which hearing protection works best in a repair shop?
NIOSH’s guidance on choosing protection fits shop life closely. It says foam earplugs aren’t a good choice for on-and-off use at dirty worksites, because you have to roll them with your fingers before each insertion. Earmuffs and pre-formed plugs are easier to take on and off when noise starts and stops. NIOSH also warns against overprotection: block too much and people pull their protection out to hear properly. Most workers need 10 dB or less of reduction to bring their exposure down.
| Type | Works well when | Watch out for |
|---|---|---|
| Foam earplugs | Clean hands, long stretches of steady noise, a spare in your toolbox | Rolling them with greasy fingers; NIOSH doesn’t recommend them for dirty, on-and-off use |
| Banded or pre-formed plugs | Quick in and out between jobs; the Minnesota study had workers try several banded styles and collected comfort feedback | Fit depends on whether your ears match the sizes on offer |
| Earmuffs | Short loud jobs like cutting or grinding, easy to grab off a hook | NIOSH notes they can get in the way of helmets, respirators and eye protection, and may not suit tight spaces |
| Custom earplugs | All-day wear, techs who’ve tried several sizes and given up, anyone who wants the same fit every time | Cost more up front and need ear impressions; NIOSH notes custom plugs are more durable and last longer |
If a cheap option is working and you wear it every time the tools run, keep using it. NIOSH puts it simply: hearing protectors that workers don’t wear aren’t a good investment.
A good shop habit: check your fit with NIOSH’s cupped-hands test. Count out loud while slowly cupping and uncupping your hands over your ears. If your voice sounds about the same both ways, your plugs are sealed.
When should you see a doctor or audiologist?
The NIDCD explains that noise can cause a temporary hearing loss that clears in 16 to 48 hours, with possible lasting damage underneath, and that loud noise can bring on tinnitus, a ringing, buzzing or roaring in the ears. If ringing or muffled hearing doesn’t fade within a couple of days, if your tinnitus is new or getting worse, if your hearing changes suddenly, or if you have ear pain, ear tubes or recent ear surgery, see a doctor or audiologist. A regular hearing test is a good idea for anyone who works around tools; our guide on what a hearing test shows explains the results.
How does Big Ear help mechanics and techs?
Custom earplugs are made from impressions of your own ears, so they go in the same way every time, with nothing to roll between greasy fingers. A few options fit shop work:
- The One is our filtered earplug. Every pair has a two-part, analog, non-electronic filter system: a non-linear filter in the canal plus an interchangeable flat filter (9, 15, 20, 25 or 30 dB) on the outside. The filters let sound through at a lower level, which can make it easier to talk with the front desk. It’s rated NRR 25 dB with one filter installed, and the filters swap in seconds. Shop noise isn’t on our standard filter guidance, so call us and we’ll talk through your tools and your day. Kits are $224.95 (Standard), $299.95 (Select, two filter sets) and $574.95 (Premium).
- Guardian Max ($149.95) is a specialty industrial earplug that lets you still hear what’s around you in very loud work.
- Guardian Vanquisher ($179.95) is our highest-NRR solid plug at NRR 37 dB, in semi-soft Shore A 45 silicone. Because NIOSH warns about overprotection, it suits people who spend long stretches with the loudest tools.
- An Industrial Lanyard or Cloth Pop Cord ($10) keeps your plugs around your neck between jobs, so they don’t end up lost under the car.
Every order includes a Home Impression Kit. It ships in 2–3 business days, the impressions take about 15–20 minutes (a helper is optional), and return postage is paid. If an impression can’t be used, we send a second kit at no charge. We hand-build every pair in the USA in 40 business days from when your impressions reach the lab, with a 30-Day Fit Warranty and a 1-year manufacturer defect warranty against manufacturing defects (loss isn’t covered). Custom products can’t be returned. With care they last 7 to 10 years. For shops outfitting a whole crew, our industrial hearing protection page and our guide to setting up protection for a team are good next steps.
Mechanic hearing FAQ
If my shift stays under the OSHA limit, am I fine?
Both studies found shifts under the OSHA legal limit, yet some (and in the tire study, most) went over the ACGIH guideline of 85 dBA, the same level NIOSH uses. NIOSH says workers at or above its 85 dBA limit are at risk of significant hearing loss over a working lifetime.
Will earplugs stop me hearing engine problems?
Heavy protection can. That’s why NIOSH recommends aiming for just enough reduction, bringing exposure down to about 75–85 dBA, and why filtered plugs that pass sound at a lower level can suit people who need to listen to their work.
Do I need plugs for every job?
NIOSH’s advice is to wear protection in noisy areas every time. A quick rule: if you’d need to raise your voice to talk to someone 3 feet away, it’s time to put them in.
Do earplugs protect against solvents?
No. NIOSH explains that these chemicals get in by breathing, swallowing or skin contact and travel through the bloodstream, so ventilation, gloves and the right respirator do that job.
Ready when you are
Take a look at Find my pair, see how the Home Impression Kit works, or call us at (719) 271-4528. Order shipping is $10. We’re happy to talk it through.
Sources
- Bejan A, Brosseau LM, Parker DL. Exposure assessment in auto collision repair shops. J Occup Environ Hyg 2011;8(7):401–408 (CDC Stacks).
- Brazile WJ, Willson-Kerns C. Noise Exposure and Evaluation at Tire-Changing Facilities. Ann Work Expo Health 2021;65(8):930–939 (CDC Stacks).
- NIOSH. Noise-Induced Hearing Loss (reviewed 30 Jan 2024).
- NIOSH. Chemical-Induced Hearing Loss (10 Apr 2024).
- NIOSH. Provide Hearing Protection (updated 28 Oct 2026).
- NIDCD. Noise-Induced Hearing Loss (last updated 16 Apr 2025).
Made for this